ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Momi Daigor
Country: Lebanon
Language: English (Spanish)
Genre: Literature
Published (Last): 10 February 2010
Pages: 76
PDF File Size: 10.90 Mb
ePub File Size: 17.85 Mb
ISBN: 783-4-13999-569-1
Downloads: 24819
Price: Free* [*Free Regsitration Required]
Uploader: Shaktijora

Within the text, the SI units are shown in brackets.

Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. When one or more of these elements is speci?

Revision to Table 2. However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. NOTE 2—Camber tolerances as shown in the table are for any wstm ft.

Combining values from the two systems will result in nonconformance with the speci? The values listed are not exact conversions of the values listed in the inch-pound tables but aetm are rounded or rationalized values.

Conformance to SI tolerances is mandatory when the “M” specification is used. NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

Individual reprints single or multiple copies of this standard may atsm obtained by contacting ASTM at the above address or at phonefaxor service astm. NOTE 2—Camber tolerances as shown in the table are for any mm length. Current edition approved March 10, For strip length under 8 ft.

  DESCARGAR AL PRINCIPIO DE LOS TIEMPOS ZECHARIA SITCHIN PDF

Table 3 shows requirements for additional elements. For strip length under mm, camber tolerance shall be subject to negotiation. Note 1—The term weight is used when inch-pound units are the standard.

ASTM A, AM_百度文库

However, under SI the preferred term in mass. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

Number of Tests and Retests Over 12 Through 11? This standard has been approved for use by agencies of the Department of Defense. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

When agreed by purchaser and supplier, other silicon ranges are permissible. The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis.

ASTM A682 Grade 1074

Conformance to SI tolerances is mandatory when the “M” specification is used. NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

  2004 4RUNNER OWNERS MANUAL PDF

When the maximum manganese limit exceeds 1. In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing. When the amount of astj, nickel, chromium, or molybdenum is less than 0. Normal coiling or piling does not provide a 3 Where an ellipsis.

ASTM International takes no position respecting the atm of any patent rights asserted in connection with any item mentioned in this standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. If any of the retests fail to comply with the requirements, the coil shall be rejected. The a6822 listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.

Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report.

Within the text, the SI units are shown in brackets.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.